SOLIDEE USBA20070 Ocean Blue Tempered Glass Vessel Sink Instruction Manual

1. Pengenalan

This manual provides comprehensive instructions for the installation, operation, and maintenance of your SOLIDEE USBA20070 Ocean Blue Tempered Glass Vessel Sink with Oil Rubbed Bronze Faucet and Pop-up Drain Set. Please read these instructions carefully before beginning installation to ensure proper function and longevity of your product. Keep this manual for future reference.

Image 1.1: The SOLIDEE Ocean Blue Tempered Glass Vessel Sink with Faucet and Pop-up Drain Set.

2. Kandungan Pakej

Verify that all components listed below are present and undamaged before proceeding with installation. If any parts are missing or damaged, please contact SOLIDEE customer support.

• Ocean Blue Tempered Glass Vessel Sink
• Oil Rubbed Bronze Faucet
• Pop-up Drain (Oil Rubbed Bronze finish)
• Talian Bekalan Air Panas dan Sejuk
• Mounting Hardware (screw packet)

Image 2.1: All components included in the SOLIDEE Vessel Sink set.

3. Spesifikasi

Image 3.1: Vessel Sink Dimensions.

Image 3.2: Faucet Dimensions.

Image 3.3: Pop-up Drain Dimensions.

4. Persediaan dan Pemasangan

Professional installation is recommended. If you are performing the installation yourself, ensure you have the necessary tools and follow all local plumbing codes. Turn off the main water supply before beginning.

Alat yang Diperlukan (Tidak Termasuk):

• Sepana Boleh Laras
• Plumber's Putty atau Silicone Sealant
• Drill (with appropriate bit for countertop material)
• Measuring Tape and Marker
• Cermin Mata Keselamatan

Langkah Pemasangan:

1. Sediakan Countertop: Determine the desired location for the sink and faucet. Mark the center for the drain hole (typically 1.75 inches to 2 inches in diameter) and the faucet hole (if separate from the sink). Carefully cut the holes using an appropriate drill bit for your countertop material.
2. Pasang Faucet: Insert the faucet into the designated hole on the countertop. Secure it from underneath with the provided washer and locking nut. Connect the hot and cold water supply lines to the faucet's inlets. Ensure connections are hand-tight, then use a wrench for a quarter turn to secure, being careful not to overtighten.
3. Install the Pop-up Drain: Apply a bead of plumber's putty or silicone sealant around the underside of the drain flange. Insert the drain into the sink's drain opening. From underneath the sink, place the rubber washer, friction washer, and locking nut onto the drain body. Tighten securely, ensuring the drain is centered and sealed.
4. Position the Vessel Sink: Carefully place the vessel sink over the countertop drain hole. Ensure it is centered and stable. Apply a thin bead of silicone sealant around the base of the sink where it meets the countertop to secure it and prevent water seepage. Allow the sealant to cure according to the manufacturer's instructions.
5. Sambung Talian Bekalan Air: Connect the hot and cold water supply lines from the faucet to the corresponding hot and cold water shut-off valves. Use an adjustable wrench to tighten connections, avoiding overtightening.
6. Ujian untuk Kebocoran: Once all connections are secure and sealant has cured, slowly turn on the main water supply. Check all connections for leaks. Run water through the faucet and check the drain for proper function and any leaks.

Imej 4.1: Berbilang views of the sink and faucet, useful for planning installation.

5. Arahan Operasi

The SOLIDEE vessel sink faucet is designed for simple operation.

• Aliran Air: Lift the single lever handle to turn on the water flow. The higher the handle is lifted, the greater the water flow.
• Kawalan Suhu: Move the lever handle to the left for hot water and to the right for cold water. Adjust the position to achieve the desired water temperature.
• Pop-up Drain: To close the drain and fill the sink, press down on the top of the pop-up drain stopper. To open the drain, press down again.

6. Penyelenggaraan

Proper care and maintenance will help preserve the finish and functionality of your SOLIDEE vessel sink and faucet set.

Membersihkan Singki:

• Clean the tempered glass sink regularly with a soft, damp kain.
• For stubborn spots, use a mild, non-abrasive glass cleaner.
• elakkan using abrasive cleaners, scouring pads, or harsh chemicals, as these can scratch the glass or damage the finish.

Cleaning the Faucet and Drain:

• Clean the Oil Rubbed Bronze (ORB) finish with a soft, damp kain.
• Mild soap and water can be used for general cleaning. Rinse thoroughly and dry with a soft cloth to prevent water spots.
• jangan use abrasive cleaners, polishes, waxes, or cleaners containing alcohol, ammonia, bleach, or other harsh chemicals, as these can damage the ORB finish.

7. Penyelesaian masalah

Rujuk jadual berikut untuk isu biasa dan penyelesaiannya.

8. Waranti dan Sokongan

For warranty information and customer support, please refer to the documentation provided with your purchase or contact SOLIDEE directly through their official website or retailer where the product was purchased. Please have your model number (USBA20070) and purchase date available when contacting support.