PGST PB-68 Door and Window Sensor User Manual

pengenalan

The PGST PB-68 Door and Window Sensor is a crucial component of your PGST Home Security System, designed to detect unauthorized entry through doors and windows. This sensor operates by detecting the separation of its two main parts, triggering an alarm signal to your connected PGST alarm host and sending notifications to your smartphone. It provides real-time monitoring and enhances the security of your home or property.

Penting: This sensor requires a PGST alarm host to function correctly and is compatible only with the PGST home security system.

Kandungan Pakej

1 x PGST PB-68 Door and Window Sensor (main unit and magnetic contact)
1 x Lithium Ion Battery (pre-installed)
1 x Double-sided Adhesive Tape for installation

Persediaan

Keperluan Pemasangan

A functional PGST alarm host (required for operation).
A clean, dry surface for mounting the sensor.

Langkah Pemasangan

Sediakan Permukaan: Clean the desired mounting area on your door or window frame and the corresponding moving part (door/window) to ensure proper adhesion.
Pasang Pita Pelekat: Apply the provided double-sided adhesive tape to the back of both the main sensor unit and the magnetic contact.
Pasang Unit Utama: Mount the larger sensor unit onto the fixed frame of the door or window.
Mount the Magnetic Contact: Mount the smaller magnetic contact onto the moving part of the door or window (the door itself or the window sash).
Jajarkan Komponen: Ensure that the main sensor unit and the magnetic contact are aligned horizontally and are less than 10 mm (approximately 0.4 inches) apart when the door or window is closed. Proper alignment is critical for correct operation.
Pemasangan Ujian: Open and close the door or window several times to verify that the sensor triggers and resets correctly. Confirm that your PGST alarm host registers the sensor's status changes.

PGST PB-68 Door and Window Sensor components, showing the main sensor unit and the magnetic contact. — This image displays the two main components of the PGST PB-68 Door and Window Sensor: the larger sensor unit and the smaller magnetic contact. These two parts are designed to be mounted adjacent to each other on a door or window frame, with a small gap between them when the door/window is closed.

Arahan Operasi

Kefungsian

Pengesanan: When the door or window to which the sensor is attached is opened, the main sensor unit and the magnetic contact separate. This separation triggers the sensor.
Pencetus Penggera: Upon being triggered, the sensor sends a signal to your connected PGST alarm host. The alarm host will then activate its siren (if armed) and initiate any programmed actions, such as sending notifications.
Pemantauan masa nyata: Through the PGST application on your smartphone, you can monitor the real-time status of your doors and windows (open or closed) 24 hours a day, 7 days a week. You will receive alarm signals on your mobile phone within seconds of a trigger event.

Pairing with PGST Alarm System

Refer to your PGST alarm host's user manual for specific instructions on how to add new sensors to the system. Generally, this involves putting the alarm host into pairing mode and then triggering the sensor (e.g., by separating its two parts) to register it with the system. The process is typically managed through the PGST mobile application.

Penyelenggaraan

Penggantian Bateri

The PGST PB-68 sensor comes with a pre-installed Lithium Ion battery. When the battery level is low, your PGST alarm host or mobile application will typically notify you. To replace the battery:

Carefully detach the main sensor unit from its mounting surface.
Open the battery compartment (refer to the sensor's casing for specific opening mechanism, usually a small latch or screw).
Remove the old Lithium Ion battery.
Insert a new 3.7V Lithium Ion battery, ensuring correct polarity.
Tutup petak bateri dan pasang semula sensor.
Test the sensor to ensure it is functioning correctly with the alarm system.

Pembersihan

Lap bahagian luar sensor dengan kain lembut dan kering. Jangan gunakan pembersih cecair atau bahan kasar, kerana ini boleh merosakkan peranti.

Menyelesaikan masalah

Masalah	Kemungkinan Punca	Penyelesaian
Sensor not triggering alarm.	Incorrect alignment of sensor and magnet. Sensor not paired with alarm host. Bateri lemah atau mati. Alarm system not armed.	Ensure the gap between the sensor and magnet is less than 10 mm when closed. Refer to your alarm host manual to pair the sensor. Gantikan bateri. Arm your PGST alarm system.
No notifications on smartphone.	Sensor not triggering. Smartphone app not configured for notifications. Internet connection issues with alarm host or smartphone.	Troubleshoot sensor triggering (see above). Check app settings for notification permissions and preferences. Verify internet connectivity for both your alarm host and smartphone.
Sensor frequently triggers falsely.	Sensor and magnet too far apart or loose. Vibrations or movement causing slight separation.	Re-align and re-secure the sensor and magnet, ensuring a firm attachment. Consider a more stable mounting location if possible.

Spesifikasi

Nombor Model	PB-68
Teknologi Sensor	Sensor Kenalan
Sumber Kuasa	Dikuasakan Bateri
Jenis Bateri	1 x Ion Litium (termasuk)
Voltage	3.7 Volt (DC)
bahan	plastik
Kaedah Pemasangan	Pelekat Diri
Jenis Pemasangan	Menonjol
Dimensi Produk	2.95 x 1.96 x 2.16 inci
Berat Barang	1.44 auns
Peranti Serasi	PGST Home Security System, Smartphone (via app)

Waranti dan Sokongan

For warranty information, technical support, or further assistance with your PGST PB-68 Door and Window Sensor, please refer to the documentation provided with your PGST alarm host or visit the official PGST website. PGST is committed to customer experience and continuously improving its products and services.

Anda juga boleh mendapatkan maklumat lanjut dan menghubungi sokongan melalui PGST Store on Amazon.

PGST PB-68