LEDONE 8FT LED Vapor Tight Light Instruction Manual

1. Pengenalan

This manual provides detailed instructions for the safe installation, operation, and maintenance of your LEDONE 8FT LED Vapor Tight Light. Please read this manual thoroughly before installation and retain it for future reference. This fixture is designed for demanding environments requiring high resistance to water, dust, and corrosion, such as parking garages, car washes, cold storage, and industrial facilities.

2. Maklumat Keselamatan

WARNING: Risk of electric shock. Disconnect power before installation or servicing.

• Installation must be performed by a qualified electrician in accordance with the National Electrical Code (NEC) and local codes.
• Pastikan bekalan voltage is compatible with the fixture's requirements (120-277Vac).
• Do not handle energized fixtures with wet hands or while standing on wet or damp permukaan.
• Jangan cuba mengubah suai atau membuka lekapan. Tiada bahagian yang boleh diservis pengguna di dalamnya.
• Pakai peralatan pelindung diri (PPE) yang sesuai semasa pemasangan.
• Pastikan lekapan dipasang dengan selamat untuk mengelakkan terjatuh.

3. Kandungan Pakej

Sahkan bahawa semua komponen ada dan tidak rosak sebelum meneruskan pemasangan.

• LEDONE 8FT LED Vapor Tight Light Fixture
• Mounting Hardware (clips, screws, anchors)
• Manual Arahan (dokumen ini)

4. Persediaan dan Pemasangan

4.1. Pra-Pemasangan

1. Matikan kuasa: Locate the circuit breaker or fuse box and turn off the power supply to the installation area. Verify power is off using a voltage penguji.
2. Bongkar: Carefully remove the fixture from its packaging. Inspect for any shipping damage.
3. Pilih Wattage and Color Temperature (CCT): Before mounting, adjust the wattage and CCT switches located on the fixture. These switches allow you to select between 60W, 80W, or 100W and 3500K, 4000K, or 5000K. Make your selection based on your lighting requirements.

Image: Product dimensions and location of wattage/CCT selection switches.

4.2. Memasang Lekapan

The fixture is designed for surface mounting. Use the provided mounting clips and hardware.

1. Mark the desired mounting locations on the ceiling or wall. Ensure the marks are level and spaced appropriately for the fixture's length.
2. Drill pilot holes at the marked locations. Insert wall anchors if mounting into drywall or masonry.
3. Pasangkan klip pelekap pada permukaan menggunakan skru yang disediakan.
4. Snap the LED vapor tight fixture into the mounted clips, ensuring it is firmly seated.

Imej: Cthample of surface mounting in a facility.

Image: Detail of the linkable design feature.

4.3. Pendawaian Elektrik

This fixture supports 0-10V dimming. Follow the wiring diagram below and local electrical codes.

• Sambungkan Hitam wayar dari lekapan ke Garisan (L) wayar daripada bekalan kuasa.
• Sambungkan putih wayar dari lekapan ke Neutral (N) wayar daripada bekalan kuasa.
• Sambungkan hijau wayar dari lekapan ke Tanah (GND) wayar daripada bekalan kuasa.
• For 0-10V dimming: Connect the Ungu wayar dari lekapan ke Malap+ wire from the 0-10V dimmer. Connect the Merah jambu/Kelabu wayar dari lekapan ke Malap- wire from the 0-10V dimmer.
• Ensure all connections are secure using appropriate wire connectors.

Note: If 0-10V dimming is not used, cap the purple and pink/gray wires individually with wire nuts.

5. Arahan Operasi

1. Hidupkan kuasa: Once installation and wiring are complete, restore power to the circuit at the breaker or fuse box. The fixture should illuminate.
2. Peredupan: If connected to a compatible 0-10V dimmer, adjust the dimmer control to achieve the desired light output level.
3. Wattage and CCT Adjustment: Wattage and CCT are set via internal switches during installation. These are not typically adjusted during normal operation. If changes are needed, disconnect power before accessing the switches.

6. Penyelenggaraan

The LEDONE Vapor Tight Light is designed for long-term, low-maintenance operation. Regular cleaning can help maintain optimal light output.

• Pembersihan: Putuskan sambungan kuasa sebelum membersihkan. Gunakan yang lembut, damp cloth with a mild, non-abrasive cleaner to wipe the exterior of the fixture. Do not use harsh chemicals or abrasive pads, as these can damage the finish or lens.
• Pemeriksaan: Periodically inspect the fixture and mounting hardware for any signs of damage, loose connections, or wear. Address any issues promptly.
• Tiada Bahagian Boleh Diservis Pengguna: The LED light source and driver are integrated components. Do not attempt to open or repair the fixture. Contact qualified personnel for any issues beyond basic cleaning and inspection.

Image: The IP65 waterproof rating ensures durability in wet conditions.

7. Penyelesaian masalah

Before performing any troubleshooting, ensure power is disconnected at the circuit breaker.

8. Spesifikasi

Image: Key features and certifications of the LEDONE Vapor Tight Light.

9. Maklumat Waranti

LEDONE products are manufactured to high quality standards. This product comes with a standard manufacturer's warranty. Please refer to the product packaging or the official LEDONE website for specific warranty terms and conditions. Keep your proof of purchase for warranty claims.

10. Sokongan Pelanggan

If you have any questions, require technical assistance, or need to report an issue, please contact LEDONE customer support:

• Webtapak: Lawati Kedai LEDONE di Amazon (for general inquiries)
• e-mel: Rujuk pembungkusan produk atau maklumat rasmi website for direct support email.
• telefon: Rujuk pembungkusan produk atau maklumat rasmi website for direct support phone number.

Please have your product model number (8FT LED Vapor Tight Light) and proof of purchase ready when contacting support.