BONTEC TV Wall Mount Instruction Manual

pengenalan

This manual provides detailed instructions for the safe and proper installation, operation, and maintenance of your BONTEC TV Wall Mount, Model CT139S. This full-motion articulated arm mount is designed to securely hold 32-70 inch flat or curved LCD/LED/OLED TVs with a maximum load capacity of 132 lbs (60 kg). It supports VESA patterns from 200x100mm up to 400x400mm.

Key features include an extra-long arm extending up to 33.5 inches, offering flexible viewing positions, and the ability to retract to just 2.56 inches from the wall for space-saving. The mount also provides ±90° swivel, ±8° tilt, and ±3° level adjustment for optimal viewing comfort. Constructed from premium cold-rolled steel, it ensures durability and safety.

Figure 1: Complete BONTEC TV Wall Mount components.

Maklumat Keselamatan

AMARAN: Read all instructions carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, consult a qualified installer. Improper installation may cause serious injury or damage.

• This product is intended for installation on wood studs, solid concrete, or brick walls. JANGAN PASANG PADA DINDING KERING SAHAJA.
• Ensure the mounting surface can safely support the combined weight of the mount and the display. The maximum load capacity for this mount is 132 paun (60 kg).
• Use only the hardware provided by the manufacturer. Using incompatible hardware may cause damage or injury.
• Sentiasa gunakan pencari stud untuk mencari stud kayu dengan tepat.
• For concrete or brick walls, ensure proper anchors are used and drilled holes are of the correct size.
• Installation often requires two people for safety and ease.

Figure 2: Diverse wall compatibility for the mount. Always ensure proper wall type and secure fastening.

Kandungan Pakej

Verify that all components are present and undamaged before beginning installation. If any parts are missing or defective, contact BONTEC customer service.

Arahan Persediaan

Langkah 1: Memasang Plat Dinding

Determine your wall type (wood stud, concrete, or brick) and follow the appropriate instructions. Use the provided template to mark drill holes accurately. A magnetic spirit level is included to ensure precise alignment.

Untuk Dinding Stud Kayu:

1. Use a stud finder to locate the edges and center of the wood studs. Mark the center of the studs where you intend to mount the wall plate.
2. Place the wall plate against the wall, aligning the mounting holes with the marked stud centers. Use the integrated spirit level to ensure it is perfectly horizontal.
3. Tandakan titik gerudi melalui lubang plat dinding.
4. Drill pilot holes into the wood studs using a 5.5mm (7/32 inch) drill bit to a depth of 60mm (2.36 inches).
5. Attach the wall plate to the wall using the Self-tap Screws (ST6.3*55mm) and Washers (φ6mm). Tighten securely with the wrench.

For Concrete or Brick Walls:

1. Place the wall plate against the wall at the desired height. Use the integrated spirit level to ensure it is perfectly horizontal.
2. Tandakan titik gerudi melalui lubang plat dinding.
3. Drill holes into the concrete or brick using a 10mm (3/8 inch) masonry drill bit to a depth of 60mm (2.36 inches).
4. Insert the Concrete Anchors (D6*50mm) into the drilled holes. Ensure they are flush with the wall surface.
5. Attach the wall plate to the wall using the Self-tap Screws (ST6.3*55mm) and Washers (φ6mm) into the anchors. Tighten securely with the wrench.

Step 2: Attaching the TV Brackets to Your TV

Select the appropriate screws (M4, M6, or M8) and spacers that fit your TV's VESA mounting holes. The VESA pattern for this mount ranges from 200x100mm to 400x400mm.

1. Letakkan TV anda dengan berhati-hati menghadap ke bawah di atas permukaan yang lembut dan bersih untuk mengelakkan calar.
2. Align the TV brackets with the VESA mounting holes on the back of your TV. Ensure the brackets are oriented correctly (usually with the longer arms pointing downwards).
3. Insert the chosen screws through the washers (if needed), then through the TV brackets, and into the TV's mounting holes. If your TV has an uneven back or recessed holes, use the appropriate spacers to ensure a flat and secure fit.
4. Ketatkan semua skru dengan kuat tetapi jangan terlalu ketat.

Step 3: Hanging TV to the Brackets and Locking It

This step typically requires two people due to the weight and size of the TV.

1. Carefully lift the TV with the attached brackets and hook the brackets onto the wall plate's arms. Ensure both brackets are securely seated on the arms.
2. Once the TV is hung, locate the locking screws or mechanisms on the bottom of the TV brackets. Tighten these screws to secure the TV to the wall plate, preventing accidental dislodgement.

Arahan Operasi

The BONTEC TV Wall Mount offers full motion capabilities for an optimal viewpengalaman dalam.

Melaraskan Kedudukan TV:

• Pelanjutan/Penarikan Balik: Gently pull the TV away from the wall to extend the arm up to 33.5 inches, or push it back to retract it to 2.56 inches.
• Pusing: The mount allows for ±90° swivel (180° total left to right movement) depending on TV size and wall clearance. Carefully pivot the TV to your desired viewsudut ing.
• Condong: The TV can be tilted ±8° to reduce glare or achieve a better viewing angle. Loosen the tilt adjustment knobs on the TV brackets, adjust the angle, and then re-tighten to secure.
• Pelarasan Tahap: If the TV appears unlevel after installation, you can adjust it by ±3°. This adjustment is typically done by loosening specific screws on the TV plate and rotating the TV slightly, then re-tightening. Refer to the detailed diagram in the installation video for precise adjustment points.

Figure 3: Extension range of the articulated arm.

Figure 4: Swivel range for flexible viewsudut-sudut.

Figure 5: Tilt and level adjustment for optimal viewing.

Pengurusan Kabel:

Use the included cable ties to neatly route and secure your TV cables along the articulated arm. This helps maintain a clean appearance and prevents cables from being pinched or damaged during adjustments.

Penyelenggaraan

Penyelenggaraan berkala memastikan ketahanan dan operasi pemasangan TV di dinding anda yang selamat.

• Pemeriksaan Berkala: Every 6-12 months, check all screws and connections to ensure they remain tight and secure. Re-tighten any loose fasteners.
• Pembersihan: Wipe the mount with a soft, dry cloth to remove dust. For stubborn marks, a slightly damp kain boleh digunakan, diikuti dengan pengeringan. Elakkan pembersih atau pelarut yang melelas.
• Pelinciran: The articulated joints are designed for smooth movement. If you notice any stiffness over time, a small amount of silicone-based lubricant can be applied to the pivot points.
• Weight Check: Do not exceed the maximum weight capacity of 132 lbs (60 kg). If you replace your TV, ensure its weight and VESA pattern are within the mount's specifications.

Menyelesaikan masalah

Berikut ialah beberapa isu biasa dan potensi penyelesaiannya:

• TV appears unlevel: Use the ±3° level adjustment feature. Loosen the relevant screws on the TV plate, adjust the TV, and re-tighten. Ensure the wall plate itself was installed level using the spirit level.
• Mount feels unstable or wobbly: Immediately remove the TV from the mount. Re-check all wall mounting screws and TV bracket screws to ensure they are securely tightened. Verify that the mount is installed into appropriate wall structures (wood studs, concrete, or brick) and not just drywall.
• Difficulty extending or swiveling the arm: Check for any obstructions. Ensure cables are not caught in the joints. Apply a small amount of silicone-based lubricant to the pivot points if movement is stiff.
• TV not fitting the VESA pattern: Double-check your TV's VESA dimensions against the mount's compatibility (200x100mm to 400x400mm). Ensure you are using the correct screws and spacers for your TV model.

If you encounter issues not listed here or require further assistance, please contact BONTEC customer support.

Spesifikasi

Maklumat Waranti

BONTEC products typically come with a manufacturer's warranty. For specific warranty terms and conditions, including duration and coverage, please refer to the warranty card included with your product or visit the official BONTEC webtapak. Simpan resit pembelian anda sebagai bukti pembelian untuk sebarang tuntutan waranti.

Sokongan

For technical support, missing parts, or any questions regarding your BONTEC TV Wall Mount, please contact BONTEC customer service. You can often find contact information on the product packaging, the official BONTEC webtapak, atau melalui peruncit tempat anda membeli produk tersebut.

Visit the official BONTEC store for more information and products: BONTEC Store on Amazon