1. Pengenalan
This manual provides essential information for the proper setup, operation, and maintenance of your LDARC X-BOSS FM900 2.4GHz FASST Receiver. Please read this manual thoroughly before using the product to ensure safe and efficient operation.
2. Produk Lebihview
Image: The LDARC X-BOSS FM900 receiver, a compact circuit board featuring surface-mount components, an integrated antenna, and clearly labeled 'FM900' branding. This image illustrates the physical design and component layout of the receiver.
3. Ciri-ciri
- Offers great reliability, stable signal link, precision antenna, and high sensitivity.
- Compact and lightweight design for various applications.
- Integrated LNA (Low Noise Amplifier) for enhanced signal reception.
- RSSI (Received Signal Strength Indicator) output for real-time signal monitoring.
4. Spesifikasi
| Spesifikasi | Perincian |
|---|---|
| item | FM900 Receiver |
| Berat badan | 1.2g |
| Dimensi | 11.5mm x 21mm |
| Voltage | 4-6V |
| Julat Kerja | >900m (air distance without electromagnetic interference) |
| Protokol | CEPAT |
| Keluaran 1 | LNA |
| Keluaran 2 | RSSI |
| Pemancar Disokong | T8FG, T14SG, T16SZ, T18SZ, T18MZ, T32MZ TX |
| Real-Time RSSI Compatibility | F3, F4, F7, etc. flight controllers |
5. Kandungan Pakej
- 1x LDARC X-BOSS FM900 Receiver
6. Persediaan
6.1. Pemasangan
Carefully connect the receiver to your flight controller or power source, ensuring correct polarity and signal connections. Mount the receiver securely in your model, away from sources of electrical interference. Position the antenna for optimal signal reception, avoiding obstructions.
6.2. Prosedur Pengikatan
To establish communication between your transmitter and the FM900 receiver, follow these general binding steps:
- Power on your transmitter and select the FASST protocol.
- Place your transmitter in binding mode (refer to your transmitter's manual for specific instructions).
- Apply power to the FM900 receiver. The receiver's LED indicator should begin to flash, indicating it is ready for binding.
- Once the binding process is complete, the receiver's LED will typically turn solid green, indicating a successful connection.
- Power cycle both the transmitter and receiver to confirm the binding is retained.
7. Arahan Operasi
After successful binding and installation, ensure your transmitter and receiver are powered on before operating your model. Always perform a range check and verify all control surfaces respond correctly before flight. Monitor the RSSI output on your flight controller or OSD (On-Screen Display) to ensure a strong signal link during operation.
8. Penyelenggaraan
- Pastikan penerima bersih dan bebas daripada habuk, kotoran dan kelembapan.
- Regularly inspect antenna connections for damage or loose contacts.
- Elakkan mendedahkan penerima kepada suhu yang melampau atau cahaya matahari langsung untuk tempoh yang lama.
- Ensure proper ventilation around the receiver during operation.
9. Penyelesaian masalah
- No Signal/Loss of Link: Re-check binding procedure. Ensure transmitter and receiver are powered on. Verify antenna connection and placement. Check for potential interference sources.
- Isyarat Sekejap-sekejap: Inspect antenna for damage. Ensure receiver is not too close to high-current wires or other electronic components that may cause interference.
- Penerima Tidak Dihidupkan: Sahkan sambungan kuasa dan voltage supply (4-6V). Check for shorts or incorrect wiring.
- Respons Kawalan Salah: Confirm correct channel mapping in your flight controller or model setup. Re-bind the receiver if necessary.
10. Maklumat Waranti dan Sokongan
LDARC products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support, please reach out to your authorized LDARC dealer or visit the official LDARC webtapak untuk mendapatkan bantuan.
