Axxess AXLOC-FD2

Axxess AXLOC-FD2 2-Channel Line Output Converter Instruction Manual for Ford 2011-Up

Model: AXLOC-FD2

pengenalan

The Axxess AXLOC-FD2 is a 2-channel line output converter designed to integrate aftermarket amplifiers with factory audio systems in select Ford vehicles from 2011 and newer. This device converts high-level speaker signals from the factory radio into low-level RCA signals, providing a clean and adjustable output for your amplifier. It also provides a 12-volt accessory output for amppenyambung menghidupkan.

Maklumat Keselamatan

  • Sentiasa putuskan sambungan terminal bateri negatif kenderaan sebelum memulakan sebarang pemasangan.
  • Pastikan semua sambungan pendawaian selamat dan terlindung dengan betul untuk mengelakkan litar pintas.
  • Rujuk pemasang audio kereta profesional jika anda tidak pasti tentang mana-mana bahagian proses pemasangan.
  • Do not operate the vehicle's audio system at excessively high volumes for prolonged periods, as this may cause hearing damage.
  • Mount the converter in a location that is protected from moisture and excessive heat.

Kandungan Pakej

Sahkan bahawa semua item hadir sebelum memulakan pemasangan:

  • AXLOC-FD2 Line Output Converter Module
  • Vehicle-specific wiring harness
  • RCA output cables
  • Remote turn-on wire
Various components of the Axxess AXLOC-FD2 kit, including the main converter module, wiring harnesses, and RCA cables.
Figure 1: Components included in the Axxess AXLOC-FD2 kit. This image displays the main converter unit, various wiring harnesses with connectors, and RCA cables, illustrating the complete set of parts for installation.

Arahan Pemasangan

This section outlines the general installation procedure. Specific vehicle disassembly instructions are beyond the scope of this manual. Refer to a vehicle-specific service manual for dash removal and access to the factory radio wiring.

Alat yang Diperlukan:

  • Pelucut wayar / pengelim
  • Pita elektrik atau tiub pengecut haba
  • Multimeter
  • Alat penyingkiran panel
  • Screwdrivers/socket set

Wiring Diagram and Connections:

  1. Putuskan Sambungan Bateri: Sebelum memulakan, tanggalkan terminal negatif bateri kenderaan untuk mengelakkan litar pintas.
  2. Access Factory Radio: Carefully remove the necessary trim panels and components to gain access to the back of the factory radio.
  3. Kenal pasti wayar pembesar suara: Using a vehicle-specific wiring diagram or a multimeter, identify the factory speaker output wires (positive and negative for each channel) from the factory radio harness.
  4. Connect Input Harness: Connect the vehicle-specific wiring harness provided with the AXLOC-FD2 to the factory radio harness. This harness will typically plug in-line with the factory radio, intercepting the speaker outputs.
  5. Connect AXLOC-FD2 Module: Plug the main connector from the vehicle-specific harness into the AXLOC-FD2 module.
  6. Sambungkan Output RCA: Connect the RCA output cables from the AXLOC-FD2 module to the RCA inputs of your aftermarket amplebih hidup.
  7. Connect Remote Turn-On: The AXLOC-FD2 provides a 12-volt accessory output (remote turn-on) for your amplifier. Connect this wire to the remote turn-on input of your amplifier. This eliminates the need to find a separate switched 12V source.
  8. Sambungan Tanah: Ensure the AXLOC-FD2 module has a solid ground connection. The vehicle-specific harness should provide this, but always verify.
  9. Pemasangan: Securely mount the AXLOC-FD2 module in a suitable location, away from heat and moisture, ensuring it does not interfere with any moving parts or vehicle components.
Axxess AXLOC-FD2 wiring harness and converter units laid out, showing the main connections.
Gambar 2: Lebihview of the AXLOC-FD2 wiring harness and converter units. This image illustrates how the main harness connects to the converter module, providing a visual guide for the primary connections during installation.
Terperinci view of the Axxess AXLOC-FD2 converter module and various connectors.
Rajah 3: Terperinci view of the AXLOC-FD2 converter module and associated connectors. This image provides a closer look at the input and output ports on the converter, as well as the design of the various plugs and sockets.

Arahan Operasi

Pelarasan Keuntungan:

The AXLOC-FD2 features adjustable gain controls to match the output level of the factory radio to the input sensitivity of your aftermarket amplifier. Proper gain setting is crucial for optimal sound quality and to prevent distortion.

  1. Tetapan Awal: Start with the gain controls on the AXLOC-FD2 set to their minimum position (fully counter-clockwise).
  2. AmpKeuntungan penguat: Set the gain control on your aftermarket amplifier to its minimum position.
  3. Main Muzik: Play a dynamic piece of music through your factory radio at about 75% of its maximum volume.
  4. Adjust AXLOC-FD2 Gain: Slowly increase the gain controls on the AXLOC-FD2 until you hear a slight distortion, then back off slightly until the sound is clean.
  5. Laraskan AmpKeuntungan penguat: Once the AXLOC-FD2 gain is set, slowly increase the gain control on your amplifier until the desired volume is achieved without distortion.
  6. Penalaan halus: Make small adjustments to both the AXLOC-FD2 and amplifier gains as needed to achieve the best sound quality. Avoid setting gains too high, as this will introduce distortion and can damage speakers.

Penyelenggaraan

The Axxess AXLOC-FD2 is designed for reliable, maintenance-free operation. No user-serviceable parts are inside. To ensure longevity:

  • Pastikan unit bebas daripada habuk dan serpihan.
  • Pastikan semua sambungan pendawaian kekal kukuh.
  • Elakkan daripada mendedahkan unit kepada suhu atau kelembapan yang melampau.

Menyelesaikan masalah

MasalahKemungkinan PuncaPenyelesaian
Tiada output audio daripada amplebih hidup
  • Loose RCA connections
  • No remote turn-on signal to amplebih hidup
  • Incorrect input wiring to AXLOC-FD2
  • Amppengalir tidak dikuasakan
  • Check and secure all RCA cables.
  • Verify remote turn-on wire is connected and receiving 12V.
  • Double-check speaker input wiring from factory radio.
  • pastikan amplifier has power and ground connections.
Kualiti bunyi yang herot atau lemah
  • Gain levels set too high
  • Sambungan tanah yang lemah
  • Incorrect speaker polarity
  • Re-adjust gain settings on AXLOC-FD2 and amplifier (refer to Operating Instructions).
  • Verify a solid, clean ground connection for both AXLOC-FD2 and amplebih hidup.
  • Check speaker wire polarity; ensure positive and negative are consistent.
Hissing or whining noise
  • Gangguan gelung tanah
  • Kabel RCA berkualiti rendah
  • Ensure all components are grounded to the same point.
  • Try routing RCA cables away from power wires.
  • Consider using higher quality shielded RCA cables.

Spesifikasi

  • model: AXLOC-FD2
  • Saluran: 2-Saluran
  • Jenis Input: High-level (speaker level)
  • Jenis Output: Low-level (RCA)
  • Keserasian: Ford vehicles 2011-Up
  • ciri-ciri: Adjustable gain, 12V remote turn-on output
  • Berat Barang: Kira-kira 1.37 paun
  • Dimensi Pakej: Kira-kira 10.39 x 10.31 x 4.92 inci

Waranti dan Sokongan

Untuk maklumat jaminan atau sokongan teknikal, sila rujuk kepada pihak berkuasa rasmi pengeluar webtapak atau hubungi bahagian perkhidmatan pelanggan mereka. Simpan bukti pembelian anda untuk tuntutan waranti.

Pengeluar: Axxess

Webtapak: axxessinterfaces.com (Cthamppautan le, pautan sebenar mungkin berbeza-beza)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.