Parkside PBS 350 A1 350W Band Saw Instruction Manual

1. Pengenalan

This manual provides essential information for the safe and efficient operation, setup, and maintenance of your Parkside PBS 350 A1 350W Band Saw. Please read these instructions thoroughly before using the tool to ensure proper function and to prevent injury or damage.

The Parkside PBS 350 A1 is designed for cutting hard and soft wood, laminate, and fiberboard. It features a powerful 350W motor with constant cutting speed, a parallel guide for precise longitudinal cuts, and an adjustable table for miter cuts.

2. Arahan Keselamatan

Always prioritize safety when operating power tools. Failure to follow these safety guidelines may result in serious injury or property damage.

• Pakai peralatan perlindungan diri (PPE) yang sesuai: Always wear safety glasses, hearing protection, and a dust mask. Gloves are recommended for handling rough materials but should be avoided near moving parts.
• Memastikan persekitaran kerja yang selamat: Keep the work area clean, well-lit, and free from obstructions. Do not operate the saw in damp atau keadaan basah.
• Selamatkan bahan kerja: Sentiasa gunakan clamps or the parallel guide to secure the material being cut. Never hold the workpiece freehand.
• Maintain proper posture: Keep a balanced stance and avoid overreaching.
• Gunakan bilah yang betul: Ensure the blade is sharp, properly tensioned, and suitable for the material being cut.
• Utilize safety features: The saw is equipped with safety interlocks on the doors and a connection for dust extraction. Ensure these are functioning correctly.
• Putuskan kuasa: Always unplug the saw before performing any adjustments, maintenance, or when changing blades.
• Pastikan tangan bersih: Never place hands or fingers near the blade while the saw is operating or connected to power. Use a push stick when cutting small pieces.
• Mengawasi kanak-kanak: Jauhkan kanak-kanak dan orang ramai dari kawasan operasi.

3. Unpacking and Included Components

Carefully unpack all items from the packaging. Inspect for any damage that may have occurred during transit. Retain packaging for future storage or transport.

Aksesori yang disertakan:

• 1 x Band Saw Blade 140 cm (pre-assembled)
• 1 x Panduan Selari
• 1 x Button Wrench
• 1 x Pemutar skru
• 3 x Kekunci Hex

Figure 3.1: Included accessories for the Parkside PBS 350 A1 band saw.

4. Persediaan

4.1 Perhimpunan Permulaan

1. Memasang Gergaji: Securely mount the band saw to a stable workbench using appropriate fasteners (not included). Ensure the saw is level and cannot tip during operation.
2. Table Adjustment: The saw table is adjustable for miter cuts. Loosen the quick-tension system knob located beneath the table. Adjust the table to the desired angle using the angle scale (0° to +45°). Tighten the knob firmly to secure the table.
3. Parallel Guide Installation: Insert the parallel guide into the slots on the saw table. Use the quick-lock mechanism to secure it for precise longitudinal cuts.

Figure 4.1: Adjustable saw table with quick-tension system and angle scale.

4.2 Blade Tension and Alignment

The band saw blade comes pre-assembled. Before first use, verify the blade tension and alignment. Refer to the markings on the saw for correct tensioning. The blade should be centered on the wheels and run smoothly without wobbling.

5. Arahan Operasi

5.1 Menghidupkan/Mematikan

• Untuk Menghidupkan: Press the green 'ON' button. The motor will start, and the blade will begin to move.
• Untuk Mematikan: Press the red 'OFF' button. The motor will stop, and the blade will slow down. Wait for the blade to come to a complete stop before leaving the machine.

Figure 5.1: Proper operation of the band saw with a push stick.

5.2 Melaraskan Ketinggian Potongan

The blade guard is adjustable for cutting heights up to 80 mm. Loosen the locking mechanism for the blade guard and slide it up or down to the desired height, ensuring it is just above the workpiece. Tighten the locking mechanism securely.

5.3 Teknik Memotong

• Potongan Lurus: Use the parallel guide for precise straight cuts. Adjust the guide to the desired width and lock it in place. Feed the workpiece slowly and steadily against the guide and into the blade.
• Miter Cuts: Adjust the saw table to the desired angle (0° to +45°) as described in Section 4.1. Secure the workpiece and feed it through the blade.
• Potongan melengkung: For curved cuts, do not use the parallel guide. Slowly guide the workpiece freehand, following your marked line. Avoid forcing the material, especially on tight curves.

Figure 5.2: Guiding a workpiece through the band saw.

6. Penyelenggaraan

Regular maintenance ensures the longevity and safe operation of your band saw. Always disconnect the power supply before performing any maintenance.

6.1 Pembersihan

• After each use, clean the saw dust and debris from the table, blade area, and motor housing using a brush or vacuum cleaner.
• Ensure the dust extraction port is clear.

Figure 6.1: Dust extraction port on the band saw.

6.2 Penggantian Bilah

When the blade becomes dull or damaged, it must be replaced. The Parkside PBS 350 A1 is compatible with standard 140 cm band saw blades up to 12 mm wide.

1. Putuskan sambungan gergaji daripada bekalan kuasa.
2. Open the safety interlocked doors to access the blade.
3. Release the blade tension mechanism.
4. Keluarkan pisau lama dengan berhati-hati.
5. Install the new blade, ensuring the teeth are pointing downwards towards the table.
6. Re-tension the blade according to the saw's markings.
7. Close the safety doors.

7. Penyelesaian masalah

Bahagian ini menangani isu biasa yang mungkin anda hadapi dengan gergaji band anda.

8. Spesifikasi

9. Waranti dan Sokongan

Information regarding specific warranty terms and conditions for the Parkside PBS 350 A1 Band Saw is not available in the provided product details. Please refer to your purchase documentation or contact the retailer for warranty information.

For technical support or spare parts inquiries, please contact Lidl customer service or visit their official webtapak. Maklumat tentang ketersediaan alat ganti tidak diberikan pada masa ini.