BIG RED TAM825051 Torin Hydraulic Low Profile Trolley Floor Jack User Manual

pengenalan

This manual provides essential instructions for the safe and effective use of your BIG RED TAM825051 Torin Hydraulic Low Profile Trolley Floor Jack. This hydraulic floor jack is designed for lifting vehicles with a maximum capacity of 2.5 tons (5,000 lb). It features a low-profile design, a single piston quick lift pump, and a safety bypass system to prevent overloading. Please read and understand all instructions and safety warnings before operation.

Maklumat Keselamatan

WARNING: Failure to heed these warnings may result in personal injury and/or property damage.

• Always wear ANSI-approved safety goggles during setup and use.
• Do not exceed the rated capacity of 2.5 tons (5,000 lb).
• Gunakan hanya pada permukaan yang keras dan rata.
• Immediately after lifting, support the vehicle with appropriate jack stands. Do not rely solely on the hydraulic jack for support.
• Do not use the jack for purposes other than lifting vehicles.
• Pastikan brek parkir kenderaan telah digunakan dan roda telah tersekat sebelum mengangkatnya.
• Keep hands and feet clear of the jack and vehicle during lifting and lowering.
• Jangan sekali-kali bekerja di bawah kenderaan yang hanya disokong oleh bicu.
• Do not modify the jack or use it with unauthorized attachments.

Kandungan Pakej

Verify that all components are present before assembly and operation:

• Bicu Lantai Hidraulik
• 2-Piece Handle
• Manual Pengguna (dokumen ini)

Perhimpunan

The BIG RED TAM825051 floor jack requires minimal assembly, primarily attaching the handle.

1. Insert the lower handle section into the handle socket on the jack.
2. Align the holes and secure the handle with the provided pin or screw, if applicable.
3. Attach the upper handle section to the lower section, ensuring it is firmly connected.

Once assembled, the handle is used for both pumping the jack and operating the release valve.

Persediaan dan Penyediaan

Before using the jack, perform the following steps:

1. Singkirkan Udara daripada Sistem Hidraulik: Before first use, or if the jack has been stored for a long time, it may be necessary to purge air from the hydraulic system. To do this, open the release valve by turning the handle counter-clockwise. Pump the handle several times to remove any trapped air. Close the release valve by turning the handle clockwise.
2. Inspect the Jack: Check for any visible damage, leaks, or loose parts. Do not use the jack if it appears damaged.
3. Sediakan Kenderaan: Letakkan kenderaan di permukaan yang keras dan rata. Tekan brek parkir dan letakkan penyekat roda pada roda yang akan kekal di atas tanah.

Image: The BIG RED TAM825051 Torin Hydraulic Low Profile Trolley Floor Jack, showcasing its compact design and red finish.

Arahan Operasi

Mengangkat Kenderaan

1. Position the jack under the vehicle's designated lifting point. Refer to your vehicle's owner's manual for correct lifting points.
2. Ensure the saddle of the jack is centered and securely contacting the lifting point.
3. Close the release valve by turning the handle clockwise until it is firm. Do not overtighten.
4. Pump the handle up and down to raise the vehicle to the desired height.
5. Once the vehicle is lifted, immediately place appropriately rated jack stands under the vehicle's frame at the manufacturer's recommended support points.
6. Slowly lower the vehicle onto the jack stands by gently turning the release valve counter-clockwise. Ensure the vehicle is stable on the jack stands before performing any work.

Image: The red BIG RED floor jack positioned under the side of a red car, ready for lifting. This demonstrates proper placement for vehicle support.

Menurunkan Kenderaan

1. Raise the vehicle slightly off the jack stands using the hydraulic jack.
2. Carefully remove the jack stands from under the vehicle.
3. Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Control the lowering speed to prevent sudden drops.
4. Once the vehicle is fully lowered, remove the jack from under the vehicle.

Penyelenggaraan

Penyelenggaraan berkala memastikan ketahanan dan operasi jek hidraulik anda yang selamat.

• Pelinciran: Keep all moving parts of the jack well-lubricated. Apply light oil to pivot points and axles periodically.
• Bendalir Hidraulik: Check the hydraulic fluid level regularly. To check, fully lower the jack, remove the oil filler plug, and ensure the fluid is at the correct level. Use only high-quality hydraulic jack oil. Do not use brake fluid or motor oil.
• Pembersihan: Pastikan bicu bersih daripada kotoran, gris dan bahan menghakis.
• Storan: Simpan bicu dalam kedudukan yang diturunkan sepenuhnya di kawasan yang bersih dan kering.

Imej: A terperinci view of the handle and release valve area of the BIG RED floor jack, highlighting key operational components.

Menyelesaikan masalah

Jika anda menghadapi masalah dengan bicu anda, rujuk masalah dan penyelesaian biasa berikut:

Spesifikasi

• Nombor Model: TAM825051
• Kapasiti Muatan: 2.5 tan (5,000 paun)
• Ketinggian Pengangkatan Minimum: 3-3/8 inches (approximately 8.57 cm)
• Ketinggian Angkat Maksimum: 14-15/16 inches (approximately 37.94 cm)
• Bahan: Keluli Aloi
• Berat Barang: 27.7 paun (kira-kira 12.56 kg)
• Dimensi Item (LxWxH): 24.5 x 10.3 x 5.7 inci (kira-kira 62.23 x 26.16 x 14.48 cm)
• Jenis Perkhidmatan Kenderaan: Car (Note: Not recommended for all SUVs and trucks due to height limitations)

Image: A visual representation of the BIG RED floor jack, indicating its minimum height of 3-3/8 inches and maximum height of 14-15/16 inches.

Waranti dan Sokongan

This BIG RED TAM825051 Torin Hydraulic Low Profile Trolley Floor Jack includes a limited 1-year manufacturer warranty. For warranty claims, technical support, or replacement parts, please contact BIG RED customer service. Keep your purchase receipt as proof of purchase.