1. Pengenalan
This manual provides essential information for the safe and efficient operation of your EPEVER MPPT Tracer2210AN G3 Solar Charge Controller. The Tracer-AN G3 series represents a new generation of MPPT solar charge controllers designed to maximize photovoltaic power utilization and extend battery life. It features independent voltage control, allowing loads to be powered even without a connected battery. This controller offers broad compatibility with both lithium and lead-acid batteries (AGM, GEL, Flooded, User types).
Sila baca manual ini dengan teliti sebelum pemasangan dan penggunaan untuk memastikan fungsi dan keselamatan yang betul.
2. Arahan Keselamatan
- Pastikan semua pendawaian dilakukan oleh kakitangan yang berkelayakan mengikut kod elektrik tempatan.
- Sentiasa putuskan sambungan panel solar dan kuasa bateri sebelum memasang atau melaraskan pengawal.
- Do not disassemble or attempt to repair the controller yourself. Contact authorized service personnel.
- Pasang pengawal di kawasan yang mempunyai pengudaraan yang baik, jauh daripada bahan mudah terbakar dan cahaya matahari langsung.
- Ensure correct polarity for all connections (PV, battery, load) to prevent damage to the controller and other components.
- Use appropriate circuit breakers or fuses for PV, battery, and load circuits.
- Wear protective eyewear when working with batteries.
3. Produk Lebihview
3.1 Ciri-ciri Utama
- Advanced MPPT technology for maximum power point tracking efficiency.
- High tracking efficiency over 99.5% and conversion efficiency up to 98%.
- Supports 12V/24VDC system voltage auto-recognition.
- Compatible with lead-acid (AGM, GEL, Flooded, User) and lithium batteries.
- Jld bebastage control for loads, enabling power supply without a connected battery.
- Low power consumption and silent operation.
- Comprehensive electronic protection functions.
- LCD display for system status and parameter settings.
3.2 Komponen dan Antara Muka
The EPEVER Tracer2210AN G3 controller features a clear interface for easy operation and monitoring.
Figure 1: EPEVER Tracer2210AN G3 Solar Charge Controller with labeled components.
| Tidak. | Komponen |
|---|---|
| 1 | Butang PILIH |
| 2 | RTS Interface (Remote Temperature Sensor) |
| 3 | Terminal PV |
| 4 | Terminal Bateri |
| 5 | Terminal Muatan |
| 6 | RS485 Interface (non-isolated) |
| 7 | Mounting Hole (Φ 5mm) |
| 8 | Butang ENTER |
| 9 | Paparan LCD |
4. Persediaan dan Pemasangan
4.1 Lokasi Pemasangan
Pilih lokasi pemasangan yang:
- Well-ventilated to dissipate heat.
- Protected from direct sunlight, high temperatures, and moisture.
- Boleh diakses untuk penyelenggaraan dan pendawaian.
- Close to the battery, but in a separate, well-ventilated compartment if possible, to avoid battery gas corrosion.
4.2 Wiring Sequence
Follow the wiring sequence carefully to prevent damage. Always connect the battery first, then the PV array, and finally the load.
- Sambungkan Bateri: Connect the battery to the controller's battery terminals. Ensure correct polarity.
- Connect the PV Array: Connect the solar panels to the controller's PV terminals. Ensure correct polarity.
- Sambungkan Beban: Connect the DC load to the controller's load terminals. Ensure correct polarity.
Gambar 2: Cthample connection sequence for the solar charge controller.
Figure 3: Detailed step-by-step connection guide.
4.3 Konfigurasi Jenis Bateri
The controller supports various battery types. For optimal charging and discharge protection, select the correct battery type in the controller settings.
Figure 4: Supported battery types including Lead-Acid (Gel, AGM, Flooded, User) and Lithium (LiFePO4, Li(NiCoMn)O2).
- Bateri Asid Plumbum: AGM, GEL, Flooded, and User-defined types are supported.
- Bateri Lithium: Supported. For detailed configuration of lithium battery parameters, optional EPEVER accessories such as a WiFi/Bluetooth adapter or a USB-RS485 cable are required.
5. Arahan Operasi
5.1 Paparan LCD
The integrated LCD displays real-time system information, including battery voltage, PV jldtage, charging current, and load status. Use the SELECT and ENTER buttons to navigate through the display menus.
5.2 Fungsi Butang
- Butang PILIH: Used to switch between different display screens or menu options.
- Butang ENTER: Used to confirm a selection or enter a menu for parameter modification.
5.3 Tetapan Parameter
Basic parameters can be viewed and adjusted directly via the LCD and buttons. For advanced settings, such as precise battery parameters or load control, external communication accessories are recommended.
Figure 5: The charge current is adjustable via a mobile application, with a minimum setting of 1A.
Optional accessories for advanced monitoring and configuration:
Figure 6: Accessory connection options (accessories not included).
6. Penyelenggaraan
Penyelenggaraan berkala memastikan jangka hayat dan prestasi optimum pengawal cas solar anda.
- Semak Sambungan: Periodically inspect all wiring connections for tightness and corrosion. Tighten any loose connections.
- Bersihkan Pengawal: Keep the controller clean and free from dust and debris. Use a dry cloth for cleaning. Do not use liquids.
- Periksa Kerosakan: Check for any physical damage to the casing, wires, or terminals.
- Pengudaraan: Ensure that the ventilation openings are not blocked to allow for proper heat dissipation.
- Kesihatan Bateri: Pantau bateri voltage and health. Ensure batteries are properly ventilated.
7. Penyelesaian masalah
Jika anda menghadapi masalah dengan pengawal anda, rujuk masalah dan penyelesaian biasa berikut:
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Tiada paparan/Tiada kuasa | Bateri tidak disambungkan atau kekutuban terbalik; Voltan bateritage terlalu rendah. | Periksa sambungan dan kekutuban bateri. Pastikan volum bateritage adalah melebihi volum operasi minimumtage. |
| Tiada pengecasan | PV array not connected or reverse polarity; PV voltage too low; PV array shaded. | Check PV connections and polarity. Ensure PV voltage is within operating range. Clear any shading. |
| Beban tidak berfungsi | Load not connected or reverse polarity; Load overcurrent/short circuit; Battery voltage terlalu rendah. | Check load connections and polarity. Reduce load or check for short circuits. Charge battery. |
| Pengawal terlalu panas | Poor ventilation; Excessive ambient temperature; Overload. | Ensure adequate ventilation. Relocate controller if ambient temperature is too high. Reduce load. |
If the problem persists after attempting these solutions, please contact EPEVER customer support or your local dealer.
8. Spesifikasi
8.1 Data Teknikal
| Parameter | Nilai |
|---|---|
| Sistem Nominal Voltage | 12/24 VDC Auto |
| Kadar Caj Semasa | 20A |
| Arus Pelepasan Berkadar | 20A |
| Rated Charge Power (12V/24V) | 260W/12V; 520W/24V |
| Maks. Litar Terbuka PV Voltage | 100V |
| Suhu Operasi | –25°C ~ +45°C |
| Ijazah Perlindungan | IP30 |
| Dimensi (L x W x H) | 220 x 154 x 52mm (8.66 x 6.06 x 2.05 inci) |
| Berat badan | 0.94kg (2.07 paun) |
| Jenis Paparan | LCD |
| bahan | plastik |
8.2 Fungsi Perlindungan
- Perlindungan Polariti Terbalik PV
- PV Overcurrent and Short Circuit Protection
- Overvol Inputtage dan Undervoltage Perlindungan
- Perlindungan Polariti Terbalik Bateri
- Battery Overcharge and Over-discharge Protection
- Load Short Circuit and Overload Protection
- Controller Overheating Protection
- Battery Side Overcurrent Protection
9. Waranti dan Sokongan
9.1 Maklumat Waranti
The EPEVER MPPT Tracer2210AN G3 Solar Charge Controller comes with a Waranti pengilang selama 2 tahun. Waranti ini melindungi kecacatan pada bahan dan mutu kerja di bawah penggunaan dan perkhidmatan biasa. Sila simpan bukti pembelian anda untuk tuntutan waranti.
9.2 Pensijilan
This product is certified with CE, FCC, IEC, ETL, and RoHS standards, ensuring compliance with international safety and environmental regulations.
9.3 Sokongan Pelanggan
For technical assistance, warranty service, or any questions regarding your EPEVER product, please contact your authorized dealer or visit the official EPEVER webtapak untuk sumber sokongan.