Nerf Modulus Ghost Ops Shadow ICS-6 Instruction Manual

Maklumat Keselamatan Penting

WARNING: CHOKING HAZARD - Small parts may be generated. Not for children under 3 years.

Do not aim at eyes or face. Use only official NERF darts. Other darts may not meet safety standards. Do not modify darts or blaster.

Pengawasan orang dewasa disyorkan semasa digunakan.

1. Persediaan

1.1 Membongkar

Keluarkan semua komponen dari pembungkusan dengan berhati-hati. Pastikan semua bahagian yang disenaraikan dalam bahagian 'Apa yang Ada di Dalam Kotak' ada.

• Blaster
• Barrel Extension
• 6 Dart
• Arahan

Image 1.1: The Nerf Modulus Ghost Ops Shadow ICS-6 blaster and its components as seen in the retail packaging.

1.2 Pemasangan Bateri

The blaster requires 3 AAA alkaline batteries for the illumination feature. Demo batteries are included.

1. Locate the battery compartment on the blaster.
2. Menggunakan pemutar skru Phillips (tidak disertakan), buka skru penutup petak bateri.
3. Insert 3 new AAA alkaline batteries, ensuring correct polarity (+/-).
4. Gantikan penutup petak bateri dan kencangkannya dengan skru.

Image 1.2: The blaster's battery requirement for its illumination feature.

1.3 Assembling the Blaster

The Illuminator Barrel can be attached to the front of the blaster.

1. Align the barrel extension with the front attachment point of the blaster.
2. Push the barrel extension firmly until it clicks into place.
3. To remove, press the release button (if present) or pull the barrel extension off.

Image 1.3: Attaching the illuminator barrel to customize the blaster.

Image 1.4: Detaching the illuminator barrel from the blaster.

2. Operating the Blaster

2.1 Memuatkan Dart

The Shadow ICS-6 blaster features a breech-load design with an internal clip system that holds up to 6 darts.

1. Open the breech by pulling back the priming handle.
2. Insert one dart at a time into the internal clip system. Ensure darts are fully seated.
3. Close the breech by pushing the priming handle forward until it locks.

Image 2.1: Loading a dart into the blaster's internal clip system.

Imej 2.2: Terperinci view of dart loading.

2.2 Menembak Blaster

Once darts are loaded and the blaster is primed:

1. Aim the blaster at a safe target.
2. Pull the trigger to fire one dart.
3. To fire another dart, repeat the loading and priming steps.

Image 2.3: The blaster and included darts.

2.3 Illumination Feature

The blaster features a clear housing that illuminates when the light activator is pressed. This allows for both stealth and illuminated modes.

• Mod Stealth: Keep the blaster clear (lights off) for discreet action.
• Illuminated Mode: Press the light activator button to illuminate the blaster, useful for low-light environments. The attached Illuminator Barrel will also light up.

Image 2.4: The blaster in illuminated mode.

Image 2.5: The blaster in clear, stealth mode.

Image 2.6: The illuminator barrel glowing when attached.

3. Penyelenggaraan

3.1 Penjagaan Am

• Keep the blaster clean by wiping it with a dry cloth. Do not use harsh chemicals or immerse in water.
• Store the blaster in a cool, dry place away from direct sunlight.
• Remove batteries if the blaster will not be used for an extended period to prevent leakage.

3.2 Dart Care

• Use only official Nerf darts to ensure optimal performance and safety.
• Inspect darts for damage before use. Damaged darts can affect performance and potentially jam the blaster.
• Do not modify darts.

4. Penyelesaian masalah

5. Spesifikasi