VTSYIQI ETCR007 AC/DC Clamp Leakage Current Sensor User Manual

1. Pengenalan

The VTSYIQI ETCR007 AC/DC Clamp Leakage Current Sensor is designed for precise measurement of AC/DC current and leakage current. It operates under line voltages up to 600V. This device utilizes advanced CT technology and digital integration for accurate, non-contact current measurement. It is suitable for various applications including power analysis, electrical testing, industrial maintenance, and scientific research.

This manual provides essential information for the safe and effective use of your ETCR007 sensor. Please read it thoroughly before operation.

2. Ciri-ciri Produk

• Fungsi: Measures AC/DC current and leakage current.
• Kaedah Pengukuran: Clip-on CT, non-contact measurement.
• Clamp Saiz: φ7mm.
• Julat input: 0mA to 60.0A AC/DC.
• Keluaran Voltage: Selectable 10mV/A or 100mV/A.
• Resolusi: 1mA AC/DC.
• Ketepatan: ±3%FS (at 23°C ±5°C, below 5%RH).
• Ralat Fasa: ≤3° (AC 50Hz/60Hz; 23°C ±2°C).
• Julat Kekerapan: AC: 45Hz-400Hz; DC: DC-100kHz.
• Antaramuka Output: BNC plug.
• Bekalan Kuasa: 9V battery (6LR61/6F22) or external power supply.
• Standard Keselamatan: Complies with IEC1010-1, IEC1010-2-032, Pollution level 2, CAT ΙΙΙ (600V).

3. Maklumat Keselamatan

To ensure safe operation and prevent electric shock or damage to the device, please observe the following safety precautions:

• Always disconnect the line being tested before opening the clamp sensor housing.
• Do not use the sensor on circuits exceeding AC600V line voltage.
• Pastikan petak bateri ditutup rapat semasa operasi.
• Do not operate the device in wet environments or if it appears damaged.
• Refer to the applicable safety rules: IEC1010-1, IEC1010-2-032, Pollution level 2, CAT ΙΙΙ (600V).
• Keep the device away from strong electromagnetic fields to avoid measurement interference.

4. Kandungan Pakej

Sahkan bahawa semua item ada dan tidak rosak semasa membongkar:

• AC / DC Clamp Leakage Current Sensor (1 piece)
• 9V Battery (6F22, 1 piece)
• User Manual / Warranty Card / Certification (1 copy)

Image 1: The VTSYIQI ETCR007 clamp sensor, output cable, and user manual, shown partially in its packaging box.

Image 2: The VTSYIQI ETCR007 clamp sensor, its attached cable, and the user manual, displayed outside of the product box.

5. Persediaan

5.1 Pemasangan Bateri

1. Cari penutup petak bateri di bahagian belakang sensor.
2. Open the cover and insert the provided 9V (6F22) battery, ensuring correct polarity.
3. Tutup penutup petak bateri dengan selamat.

5.2 Connecting the Output Wire

The sensor comes with an integrated output cable. The core wire provides the signal positive output, and the shielding wire serves as the signal ground. Connect the BNC plug of this cable to a compatible measuring instrument (e.g., digital multimeter, oscilloscope, power quality analyzer).

Imej 3: Perincian view of the BNC connector at the end of the sensor's output cable, ready for connection to a measuring device.

6. Operasi

6.1 Powering On and Range Selection

1. Locate the POWER switch on the sensor.
2. Slide the switch to select the desired output range: 10mV/A or 100mV/A. The "OFF" position powers down the device.
3. The selected range determines the output voltage setiap ampere of measured current. For example, 100mV/A means 100mV output for every 1A of current.

Imej 4: Gambar jarak dekat view of the sensor's control panel, showing the power switch with 10mV/A, 100mV/A, and OFF positions.

6.2 Penentukuran Sifar

Before taking measurements, especially for DC current or leakage current, it is crucial to perform a zero calibration to eliminate external electric field interference and ensure accuracy.

1. Ensure no current is flowing through the clamp Rahang.
2. Locate the ZERO adjustment knob (often a rotary knob) on the sensor.
3. Rotate the knob until the connected measuring instrument displays zero current.

Imej 5: Perincian view dari klamp jaw and the area where the zero adjustment knob is typically located, indicated by a yellow arrow symbol.

6.3 Mengambil Ukuran

1. Buka clamp rahang dengan menekan picu.
2. Place the wire carrying the current to be measured inside the center of the clamp jaw. Ensure only one conductor is within the jaw for accurate measurement.
3. Release the trigger to close the clamp jaw securely around the conductor.
4. Read the current value from your connected measuring instrument, applying the selected output ratio (e.g., if 100mV/A is selected and the instrument reads 500mV, the current is 5A).
5. For optimal accuracy, ensure the tested wire is positioned in the jaw's center.

Imej 6: Pro sampinganfile of the VTSYIQI ETCR007 clamp sensor, showing the ergonomic design for gripping and clamping around a conductor.

7. Spesifikasi

Image 7: The back of the sensor, displaying a product label with model information, specifications, and a barcode (00770112).

8. Penyelenggaraan

• Pembersihan: Use a soft, dry cloth to clean the sensor. Do not use abrasive cleaners or solvents.
• Storan: When not in use for extended periods, remove the battery to prevent leakage. Store the device in a dry environment, away from direct sunlight and extreme temperatures.
• Penggantian Bateri: Replace the 9V battery when the power indicator light dims or the device fails to power on.
• Penentukuran: Regular calibration by a qualified technician is recommended to maintain measurement accuracy, especially after prolonged use or if accuracy is suspected to have drifted.

9. Penyelesaian masalah

10. Waranti dan Sokongan

This VTSYIQI ETCR007 AC/DC Clamp Leakage Current Sensor comes with a Waranti 1 tahun dari tarikh pembelian, meliputi kecacatan pada bahan dan mutu kerja di bawah penggunaan biasa.

For technical support, warranty claims, or service inquiries, please contact the manufacturer:

• Pengeluar: VETUS INSTRUMENTS
• E-mel hubungan: ericbai@vetusgroup.cn

Sila simpan resit pembelian anda sebagai bukti pembelian untuk tujuan waranti.