GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

pengenalan

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Maklumat Keselamatan

AMARAN: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Ensure power is OFF at the circuit breaker before installation.
• Peranti ini bertujuan untuk pemasangan mengikut Kod Elektrik Kebangsaan dan peraturan tempatan.
• Do not use in wet locations or where directly exposed to water.
• Untuk kegunaan dalaman sahaja.

Kandungan Pakej

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Skru Pemasangan
• Wire Nuts (may vary by package)
• Manual Pengguna (dokumen ini)

Persediaan dan Pemasangan

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Turn OFF Power: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Keluarkan Suis Lama: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Kenal pasti wayar:
   • Talian (Panas): Usually black, coming from the circuit breaker.
   • Muatkan: Usually black, going to the light fixture or appliance.
   • neutral: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Tanah: Usually green or bare copper.
4. Sambungkan Suis Baharu: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Sambungkan Talian wire to the terminal marked "LINE".
   • Sambungkan Muatkan wire to the terminal marked "LOAD".
   • Sambungkan Berkecuali wire to the terminal marked "NEUTRAL".
   • Sambungkan tanah wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Suis Pemasangan: Tolak suis berwayar ke dalam kotak dinding dengan berhati-hati. Pasangkannya dengan skru yang disediakan.
6. Pasang Plat Dinding: Attach the new or existing wall plate.
7. Pulihkan Kuasa: HIDUPKAN semula kuasa pada pemutus litar.

Rajah 1: Depan view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle sekali. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Mengendalikan Suis

Kawalan Manual

• Tekan ke atas of the paddle to turn the connected load ON.
• Tekan ke bawah of the paddle to turn the connected load DIMATIKAN.

Kawalan Gelombang Z

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Penyelenggaraan

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Pembersihan: Untuk membersihkan suis, lap dengan kain lembutamp kain. Jangan gunakan pembersih atau pelarut yang melelas.
• Kemas kini Firmware: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Penjagaan Am: Pastikan suis tidak terdedah kepada kelembapan berlebihan atau suhu yang melampau.

Menyelesaikan masalah

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle sekali. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Spesifikasi

Waranti dan Sokongan

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webtapak atau hubungi bahagian perkhidmatan pelanggan mereka.

Webtapak: www.gocontrol.com

Pengeluar: GOCONTROL