INSIZE ISM-M2000 Metallurgical Microscope User Manual

1. Pengenalan

The INSIZE ISM-M2000 Metallurgical Microscope is a precision instrument designed for high magnification observation and detailed metallurgical image analysis. This manual provides comprehensive instructions for the proper setup, operation, and maintenance of your microscope to ensure optimal performance and longevity.

Gambar 1: Lebihview of the INSIZE ISM-M2000 Metallurgical Microscope. This image shows the complete microscope unit, including the binocular head, objective turret, mechanical stage, and external power supply unit.

2. Ciri-ciri Utama

• kanta mata: Wide field 10X eyepiece with a view field of 87 inches.
• Stage: Double-layer mechanical stage, size 6.30×5.51 inches, with a travel range of 2.95×1.97 inches (0.1mm/.004 inches precision).
• Pencahayaan: 12V/50W halogen lamp for bright and consistent lighting.
• Penapis: Built-in green, yellow, blue, gray, and frosted glass filters for enhanced contrast and observation.
• Jarak Murid: Adjustable interpupillary distance from 1.89 to 2.95 inches for comfortable viewing.
• Permohonan: Optimized for high magnification observation and metallurgical image analysis.

3. Panduan Persediaan

1. Membongkar: Keluarkan semua komponen daripada pembungkusan dengan berhati-hati. Simpan pembungkusan asal untuk pengangkutan atau penyimpanan pada masa hadapan.
2. penempatan: Place the microscope on a stable, level surface, away from direct sunlight, vibrations, and excessive dust. Ensure adequate space around the unit for operation and ventilation.
3. Pemasangan Kanta Mata: Insert the 10X wide field eyepieces into the binocular tubes. Gently push them down until they are seated firmly.
4. Sambungan Kuasa: Connect the power cord from the microscope's illumination unit to a suitable power outlet (12V/50W halogen lamp). Ensure the power switch is in the "OFF" position before connecting.
5. Pemeriksaan Awal: Before powering on, visually inspect all components to ensure they are securely attached and free from damage.

4. Arahan Operasi

1. Hidupkan kuasa: Turn on the main power switch located on the illumination unit. Adjust the brightness control knob to a comfortable level.
2. Sample Penempatan: Place the metallurgical sample securely on the double-layer mechanical stage. Gunakan stage clips to hold it in place if necessary.
3. Objective Selection: Rotate the revolving nosepiece to select the desired objective lens. Start with the lowest magnification objective for initial focusing.
4. Memfokuskan:
   • Gunakan coarse focus knob (larger knob) to bring the sample into approximate focus.
   • Gunakan fine focus knob (smaller knob) for precise focusing and to achieve a sharp image.
5. Stage Pergerakan: Use the X-Y control knobs on the mechanical stage to move the sample horizontally and vertically across the field of view.
6. Pelarasan Jarak Antara Pupil: While looking through the eyepieces, adjust the distance between the two eyepiece tubes until you see a single, clear circular field of view.
7. Pelarasan Diopter: If one eye is clearer than the other, adjust the diopter ring on one of the eyepieces until both eyes perceive a sharp image.
8. Penggunaan penapis: Utilize the built-in green, yellow, blue, gray, or frosted glass filters by sliding them into position to enhance contrast or reduce glare for specific sampjenis le.
9. Matikan: After use, turn off the illumination and then the main power switch.

5. Penyelenggaraan

• Pembersihan Optik: Use a soft, lint-free cloth specifically designed for optical lenses to clean eyepieces and objectives. For stubborn smudges, a small amount of lens cleaning solution can be applied to the cloth, not directly to the lens.
• Pembersihan Am: Wipe the microscope body with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
• Perlindungan Debu: Always cover the microscope with a dust cover when not in use to prevent dust accumulation on optical and mechanical parts.
• Storan: Store the microscope in a cool, dry place, away from extreme temperatures and humidity.
• Lamp Penggantian: Jika halogen lamp burns out, ensure the microscope is unplugged and cool before carefully replacing it with a new 12V/50W halogen lamp. Refer to the lamp housing for specific replacement instructions.

6. Penyelesaian masalah

7. Spesifikasi

8. Waranti dan Sokongan

Specific warranty information for the INSIZE ISM-M2000 Metallurgical Microscope is typically provided at the point of purchase or within separate documentation included with the product. Please refer to your purchase receipt or contact your vendor for details regarding warranty coverage.

For technical support, service, or inquiries about replacement parts, please contact INSIZE customer service or your authorized INSIZE distributor. Contact information can usually be found on the manufacturer's official webtapak atau pada pembungkusan produk.