pengenalan
This manual provides detailed instructions for the installation, operation, and maintenance of the DIGITEN G1 Water Flow Sensor, Model FL-808. This Hall effect flow sensor is designed for accurate measurement of liquid flow within a range of 1 to 60 liters per minute. Please read this manual thoroughly before use to ensure proper function and safety.
Produk Selesaiview
The DIGITEN G1 Water Flow Sensor (Model FL-808) is a robust and reliable device for measuring water flow. It features G1 (0.5 inch) threaded connections for easy integration into various systems. The sensor outputs a square wave pulse signal proportional to the flow rate, making it suitable for microcontrollers and other electronic systems.
Ciri-ciri Utama:
- Pembinaan Tahan Lama: Waterproof, heat-resistant, pressure-resistant, and cold-resistant design.
- Julat Aliran Lebar: Measures flow from 1 to 60 Liters per minute.
- Pemasangan Mudah: Simple G1 (0.5 inch) threaded connections.
- Keluaran Nadi: Generates a square wave pulse signal for flow rate calculation.
- Mematuhi RoHS: Memenuhi piawaian alam sekitar.
Maklumat Keselamatan
- Pastikan bekalan kuasa diputuskan sebelum pemasangan atau penyelenggaraan.
- Do not exceed the maximum operating pressure of 1.75 MPa.
- Verify correct wiring connections to prevent damage to the sensor or connected equipment.
- Avoid installing the sensor in locations with extreme vibrations or corrosive environments.
- This device is intended for water flow measurement. Do not use with other liquids without verifying compatibility.
Kandungan Pakej
- 1 x DIGITEN G1 Water Flow Sensor (Model FL-808)
Spesifikasi Teknikal
| Model | FL-808 |
| bahan | Metal (Internal components), Plastic (Housing) |
| Inlet/Outlet Connection Size | G1 (0.5 inch) Threaded |
| Julat Kadar Aliran | 1 - 60 L/min |
| Tekanan Operasi Maks | 1.75 MPa (17.5 Bar) |
| Vol Operasitage Julat | DC 5 - 24 V |
| Arus Operasi | Cannot exceed 10 mA (at DC 5V) |
| Isyarat Output | Square Wave Pulse |
| Frequency Formula | F = 4.8 * Q (L/min) ± 2% |
| Output Pulse per Liter | Approximately 450 pulses/liter |
| Suhu Operasi | ≤ 80°C |
| Kelembapan Operasi | 35% - 90% RH |
| Suhu Penyimpanan | -25°C hingga +80°C |
| Kelembapan Penyimpanan | 25% - 95% RH |
| Rintangan Penebat | > 100 MΩ |
| Panjang Kabel | 15 sm |
| Berat Produk | 80 gram |
Persediaan dan Pemasangan
1. Pemasangan Mekanikal
The flow sensor features G1 (0.5 inch) male threaded connections on both ends. Ensure the flow direction arrow on the sensor body aligns with the intended water flow in your system. Apply appropriate thread sealant (e.g., PTFE tape) to prevent leaks. Tighten connections securely but do not overtighten.
Rajah 1: Depan view of the DIGITEN G1 Water Flow Sensor, showing the G1 threaded connections and the product label.
Figure 2: Technical drawing illustrating the dimensions and internal structure of the DIGITEN G1 Water Flow Sensor.
2. Pendawaian Elektrik
The sensor has a 3-wire connection. Connect the wires as follows:
- Kawat Merah: VCC (+) - Connect to DC 5V to 24V power supply.
- Kawat Hitam: GND (-) - Connect to ground.
- Kawat kuning: Signal Output - Connect to your microcontroller or data acquisition system's input pin.
Pastikan vol operasitage is within the specified range of DC 5-24V. The current drawn by the sensor should not exceed 10mA at 5V DC.
Rajah 3: Jarak dekat view of the sensor's wiring connections: Red (VCC), Black (GND), and Yellow (Signal).
Rajah 4: Terperinci view of the 3-pin connector attached to the sensor's cable.
Arahan Operasi
Prinsip Operasi
The DIGITEN G1 Water Flow Sensor uses a Hall effect sensor to detect the rotation of an internal turbine. As water flows through the sensor, it spins a turbine, and a magnet attached to the turbine generates a series of electrical pulses. The frequency of these pulses is directly proportional to the flow rate of the water.
Flow Rate Calculation
The output signal is a square wave. The flow rate (Q in L/min) can be calculated from the measured frequency (F in Hz) using the following formula:
F = 4.8 * Q (L/min)
Therefore, to find the flow rate:
Q (L/min) = F / 4.8
The sensor provides approximately 450 pulses per liter of water. The accuracy is ±2%.
Gambar 5: Dalaman view of the sensor, highlighting the turbine mechanism responsible for pulse generation.
Figure 6: The sensor with its label clearly visible, detailing model number, working range, and wiring information.
Penyelenggaraan
- Pemeriksaan Berkala: Periodically check for any signs of leaks at the connections or damage to the sensor body and wiring.
- Pembersihan: If the sensor's accuracy degrades, it may be due to debris accumulation inside the turbine. Disconnect power and water supply, then carefully remove the sensor for inspection and cleaning. Use a soft brush and clean water to remove any obstructions.
- Storan: If storing the sensor for an extended period, ensure it is clean, dry, and kept within the specified storage temperature and humidity ranges (-25°C to +80°C, 25%-95% RH).
Menyelesaikan masalah
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Tiada keluaran isyarat |
|
|
| Inaccurate flow readings |
|
|
| Kebocoran pada sambungan |
|
|
Waranti dan Sokongan
For warranty information or technical support, please contact DIGITEN customer service through the retailer where the product was purchased or visit the official DIGITEN website. Please have your product model number (FL-808) and purchase details ready when contacting support.