1. Arahan Keselamatan Penting
Sentiasa baca dan fahami semua amaran keselamatan, arahan, ilustrasi dan spesifikasi yang disediakan dengan alat kuasa ini. Kegagalan mematuhi semua arahan yang disenaraikan di bawah boleh mengakibatkan renjatan elektrik, kebakaran dan/atau kecederaan serius. Simpan semua amaran dan arahan untuk rujukan masa hadapan.
- Wear eye protection and hearing protection.
- Jauhkan tangan dari kawasan pemotongan.
- Pastikan bahan kerja berada dalam keadaan selamatamped.
- Disconnect power before changing blades or performing maintenance.
- Use only blades specified for this tool and material.
- Pastikan kawasan kerja bersih dan terang.
- Jangan kendalikan alatan kuasa dalam suasana mudah letupan.
- Avoid accidental starting. Ensure the switch is in the off-position before connecting to power.
2. Produk Lebihview
The Ferm MSM1037 Mitre Saw is a powerful 1300W tool designed for precise cutting of various materials including metal, nylon, plastic, stainless steel, and wood. It features a 210mm saw blade and operates at 4500 RPM.
Rajah 1: Depan view of the Ferm MSM1037 Mitre Saw, showing the blade, base, and handle assembly.
3. Persediaan dan Pemasangan
3.1 Membongkar
Keluarkan semua komponen dari pembungkusan dengan berhati-hati. Periksa sebarang kerosakan yang mungkin berlaku semasa transit. Simpan pembungkusan untuk penyimpanan atau pengangkutan masa hadapan.
3.2 Mengamankan Gergaji
Mount the mitre saw securely to a stable workbench using appropriate bolts and washers. Ensure the saw is level and does not wobble during operation.
3.3 Pemasangan Bilah
- Putuskan sambungan gergaji daripada bekalan kuasa.
- Tekan butang kunci gelendong.
- Gunakan sepana yang disediakan untuk melonggarkan bolt penahan bilah.
- Tanggalkan bebibir luar dan bilah lama.
- Pasang bilah 210mm yang baharu, pastikan arah putaran sepadan dengan anak panah pada pelindung.
- Replace the outer flange and tighten the retaining bolt securely.
- Lepaskan kunci gelendong.
4. Arahan Operasi
4.1 Melaraskan Sudut Mitre
To adjust the mitre angle, loosen the mitre lock knob. Rotate the turntable to the desired angle, indicated on the scale. Tighten the mitre lock knob firmly to secure the position.
Rajah 2: Jarak dekat view of the mitre angle scale on the saw base, showing markings from 0 to 45 degrees left and right.
4.2 Melaraskan Sudut Serong
For bevel cuts, loosen the bevel lock lever located at the rear of the saw. Tilt the saw head to the desired angle (up to 45 degrees). Securely tighten the bevel lock lever.
Figure 3: Detail of the bevel angle adjustment mechanism, showing the scale and locking lever for tilting the saw head.
4.3 Membuat Potongan
- Place the workpiece firmly against the fence and clamp ia dengan selamat.
- Ensure the blade is clear of the workpiece before starting the motor.
- Press the trigger switch to start the motor and allow the blade to reach full speed.
- Slowly lower the saw blade through the workpiece.
- Setelah potongan selesai, lepaskan suis picu dan biarkan bilah berhenti sepenuhnya sebelum mengangkat kepala gergaji.
5. Penyelenggaraan
5.1 Pembersihan
Regularly clean the saw to remove sawdust and debris. Use a brush or vacuum cleaner. Do not use solvents that may damage plastic parts.
5.2 Pemeriksaan Bilah
Inspect the saw blade before each use for sharpness, cracks, or missing teeth. Replace damaged or dull blades immediately.
5.3 Berus Karbon
The carbon brushes may need periodic replacement. Consult a qualified service technician for this procedure.
6. Penyelesaian masalah
| Masalah | Kemungkinan Punca | Penyelesaian |
|---|---|---|
| Saw tidak bermula | Tiada bekalan kuasa; Suis rosak; Berus karbon usang | Check power connection; Test switch; Replace carbon brushes (professional service recommended) |
| Bilah tidak memotong dengan bersih | Dull blade; Incorrect blade for material; Blade installed incorrectly | Replace blade; Use appropriate blade; Reinstall blade correctly |
| Getaran yang berlebihan | Loose blade; Damaged blade; Unsecured saw | Tighten blade bolt; Replace blade; Secure saw to workbench |
7. Spesifikasi
- Nombor Model: MSM1037
- Kuasa: 1300W
- Voltage: 240 Volt
- Diameter Bilah: 210mm
- Kelajuan: 4500 RPM
- Sudut Pemotongan: 45 Degrees (Mitre and Bevel)
- Number of Teeth (Blade): 80
- Berat Barang: 6 Kilogram
- Dimensi Produk: 42 x 40 x 30 cm
- Syor Permukaan: Metal, Nylon, Plastic, Stainless Steel, Wood
- Sumber Kuasa: Elektrik Bertali
8. Waranti dan Sokongan
For warranty information and technical support, please refer to the documentation provided with your purchase or contact Ferm customer service. Keep your purchase receipt as proof of purchase.
Pengeluar: Bosch (as per product data)
Tarikh Mula-mula Tersedia: 15 Oktober 2015