BIG RED T43006 Torin Steel Jack Stands Instruction Manual

pengenalan

These BIG RED T43006 Torin Steel Jack Stands are designed to safely support vehicles after they have been lifted by a jack. They feature a 3-ton (6,000 lb) capacity per pair and are suitable for SUVs and extended height trucks. Constructed from high-grade steel with a welded frame, these jack stands meet ASME safety standards, ensuring reliable performance for automotive maintenance and repair tasks.

Maklumat Keselamatan Penting

AMARAN: Failure to read, understand, and follow all instructions and warnings may result in serious injury or property damage. Always prioritize safety when working with vehicles.

• Baca Manual: Before using these jack stands, thoroughly read and understand all instructions and warnings provided in this manual.
• Kapasiti Dinilai: Never exceed the rated capacity of 3 tons (6,000 lbs) per pair. The load must be evenly distributed between the two jack stands.
• Permukaan Aras: Always use jack stands on a hard, level, non-slippery surface. Avoid using them on soft ground, asphalt, or uneven surfaces.
• Penempatan yang betul: Position the jack stands only under the vehicle's frame or axle points specified by the vehicle manufacturer. Consult your vehicle's owner's manual for proper lifting and support points.
• Semakan Kestabilan: After placing the jack stands and lowering the vehicle onto them, gently rock the vehicle to ensure it is stable and securely supported before beginning any work.
• Gunakan secara Berpasangan: Always use jack stands in pairs. Never use a single jack stand to support a vehicle.
• Elakkan Pergerakan: Do not move or adjust the jack stands while the vehicle is supported on them.
• Peralatan Pelindung Diri: Wear appropriate safety gear, such as safety glasses and gloves, when working under a vehicle.
• Kanak-kanak dan Penonton: Jauhkan kanak-kanak dan orang yang tidak dibenarkan dari kawasan kerja.

Persediaan

1. Inspect Jack Stands: Before each use, inspect both jack stands for any signs of damage, wear, or deformation. Do not use damaged jack stands.
2. Sediakan Kawasan Kerja: Ensure your work area is clean, well-lit, and on a hard, level surface. Engage the vehicle's parking brake and block the wheels that will remain on the ground.
3. Kenderaan Angkat: Use a suitable floor jack to lift the vehicle to the desired height. Refer to your vehicle's owner's manual for proper jacking points.
4. Kedudukan Jek Berdiri: Once the vehicle is lifted, carefully position the jack stands under the vehicle's designated support points (e.g., frame rails, axle housing).

Arahan Operasi

1. Laraskan Ketinggian: With the vehicle lifted by a jack, pull the handle on the jack stand to release the locking pawl. Adjust the ratchet bar to the desired height, ensuring the saddle makes contact with the vehicle's support point. Release the handle to lock the ratchet bar into place.
2. Kenderaan Selamat: Slowly and carefully lower the vehicle onto the jack stands using the floor jack. Ensure the vehicle's weight is fully resting on the jack stands and not on the floor jack.
3. Sahkan Kestabilan: Before working under the vehicle, gently push and pull on the vehicle to confirm it is stable and securely supported by both jack stands.
4. Removing Jack Stands: When work is complete, use the floor jack to lift the vehicle slightly off the jack stands. Pull the handle on each jack stand to release the ratchet bar and lower it to its minimum height. Remove the jack stands from under the vehicle, then slowly lower the vehicle to the ground using the floor jack.

Penyelenggaraan

• Pemeriksaan Berkala: Periodically inspect the jack stands for any signs of rust, cracks, bends, or other damage. Pay close attention to the welded joints and the condition of the ratchet bar and locking mechanism.
• Pembersihan: Keep the jack stands clean and free from dirt, grease, and debris. Wipe them down with a clean cloth after each use.
• Pelinciran: Lightly lubricate the ratchet bar and locking mechanism with a general-purpose lubricant to ensure smooth operation and prevent corrosion.
• Storan: Store jack stands in a dry, clean area when not in use to prevent rust and damage.
• Damaged Units: If any part of the jack stand is damaged or shows excessive wear, discontinue use immediately and replace the unit. Do not attempt to repair damaged jack stands.

Menyelesaikan masalah

These jack stands are mechanical devices with minimal components. Most issues relate to improper use or maintenance.

• Kesukaran Melaraskan Ketinggian:
  • Ensure the handle is fully pulled to disengage the locking pawl.
  • Check for debris or rust on the ratchet bar or within the mechanism. Clean and lubricate as necessary.
• Instability After Placement:
  • Verify the jack stands are on a hard, level surface.
  • Ensure the vehicle's weight is centered on the saddle of each jack stand.
  • Confirm the ratchet bar is fully engaged and locked at the desired height.
  • Never work under an unstable vehicle. Re-position and re-secure the vehicle immediately.

Spesifikasi

Waranti dan Sokongan

These BIG RED T43006 Torin Steel Jack Stands come with a limited 1-year manufacturer warranty. For warranty claims, technical support, or inquiries, please contact Torin customer service.

Manufacturer Contact Information: ISSAQUAH, WA, 98027 US

Untuk sokongan tambahan, anda boleh melawati BIG RED brand page on Amazon.